Network devices often encounter various faults, which not only lead to degraded network performance but also may cause business interruptions, resulting in unnecessary losses.
Network faults occur frequently, and troubleshooting them can be challenging. However, being adept at reviewing and organizing can significantly improve work efficiency.
Today, let’s talk about common network faults and troubleshooting strategies that network engineers encounter in their daily work. The six faults mentioned next are undoubtedly familiar to everyone. If you can resolve them, congratulations, you are one step closer to becoming a technical expert.
When the switch is powered on, devices in the network cannot communicate normally.
01 Possible Causes
Unstable power supply or insufficient voltage
Hardware failure of the switch
Network configuration errors
Incorrect port connection or physical layer faults
02 Troubleshooting Steps
Check Power Supply: Ensure the switch power cord is correctly connected and the power adapter is functioning properly.
Observe Indicator Lights: Check the status of the indicator lights on the switch to confirm if the power light is on normally.
Inspect Hardware: Check if the switch ports are damaged, and ensure the cables are correctly connected and undamaged.
Review Configuration: Log in to the switch management interface to check if VLAN configuration, port mode (such as access or trunk), etc., are correctly set.
Test Connectivity: Use the ping command to test the connectivity between switch ports and other devices.
03 Solutions
If the power supply is unstable or the voltage is insufficient, consider replacing the power adapter or using a voltage regulator.
If hardware failure is detected, contact the supplier for repair or replacement.
For configuration errors, reconfigure VLAN, port mode, etc., according to the network design.
If a port is damaged, replace the affected port or the entire switch.
2 5-Port Switch Only Allows 4 Ports
In an office with 4 computers, but only one information outlet, a 5-port (one port is an UpLink port) switch was configured.
Originally, it was thought that 4 computers would connect to 4 ports, and 1 UpLink port would connect to the LAN. However, after connecting to the network, the port adjacent to the UpLink port (port 1) cannot be used normally.
01 Fault Analysis
The UpLink port should not be considered as a separate port because it is essentially the same port as the adjacent one, just for different connection purposes. With the UpLink port, hub devices can use straight-through cables to connect to another hub device’s ordinary port, eliminating the need for crossover cables.
Switches and hubs usually have ×4 chips, so their ports are mostly 4-port, 8-port, 16-port, 24-port, etc. If a 5-port is made, 3 modules would be wasted, increasing costs.
02 Fault Resolution
Replace the 4-port switch with an 8-port switch to resolve the issue.
3 “COL” Indicator Light Constantly On or Flashing but Unable to Communicate
The “COL” (Collision) indicator light on the network device (usually a switch or router) is constantly on or flashing, indicating a line conflict, causing abnormal network communication.
01 Possible Causes
Incorrect connection configuration between network devices
Using half-duplex mode instead of full-duplex mode
Broadcast storm or excessive traffic in the network
Hardware failure or cable quality issues
02 Troubleshooting Steps
Check Connections: Ensure all connections between network devices are correct, including cable types and connection methods.
Check Port Settings: Log in to the device management interface to check if the port working mode (half-duplex or full-duplex) matches.
Monitor Network Traffic: Use network monitoring tools to analyze network traffic and check for broadcast storms or other abnormal traffic.
Test Cables: Use a cable tester to check the quality of the cables, ensuring no physical damage.
Restart Devices: Try restarting the devices to clear potential temporary faults.
03 Solutions
Adjust device port settings to full-duplex mode.
If a broadcast storm is detected, isolate the affected devices or network segments.
Replace cables with quality issues.
Update device firmware to fix potential software issues.
In severe cases, replace faulty hardware.
4 Server Connection Intermittent After Upgrading to Gigabit Network
After upgrading the network to gigabit speed, the connection between the server and clients becomes unstable, showing intermittent connectivity.
01 Possible Causes
Incompatible network devices
Network configuration errors
Hardware failure
Cable quality issues
02 Troubleshooting Steps
Check Device Compatibility: Ensure all network devices (such as switches, routers, servers, etc.) support gigabit speed.
Check Port Settings: Log in to the device management interface to check if the port working mode (auto-negotiation or fixed speed) is correctly set.
Test Cables: Use a gigabit tester to check if the cables support gigabit speed, especially CAT5e or higher-grade cables.
Monitor Network Traffic: Use network monitoring tools to analyze network traffic and check for traffic bottlenecks.
Update Firmware: Ensure all network devices have the latest firmware versions and update them as needed.
03 Solutions
Upgrade incompatible devices to models that support gigabit speed.
Adjust device port settings to auto-negotiation mode or manually set to gigabit speed.
Replace cables with quality issues.
Add necessary buffers between devices or adjust QoS (Quality of Service) settings to optimize traffic control.
5 Link Light Flashing but Network Speed is Extremely Slow
The Link light on the network device (such as a switch or router) shows a normal connection, but the actual network transmission speed is very slow.
01 Possible Causes
Network congestion
Cable or connector issues
Device configuration errors
Hardware failure
02 Troubleshooting Steps
Check Network Load: Use network monitoring tools to check if the network is under high load.
Test Cables: Use a cable tester to check the quality of the cables, ensuring no physical damage.
Check Device Configuration: Log in to the device management interface to check if port settings, VLAN configuration, etc., are correctly set.
Restart Devices: Try restarting the devices to clear potential temporary faults.
Inspect Hardware: Check the hardware status of the devices, including fans, power supplies, etc., to ensure they are functioning properly.
03 Solutions
Optimize network traffic to reduce congestion, such as increasing bandwidth, adjusting QoS strategies, etc.
Replace cables or connectors with quality issues.
Reconfigure device ports and VLAN settings according to the network design.
If hardware failure is detected, consider replacing faulty components or the entire device.
6 Hub and Router Cannot Share Internet
In a small network environment, using a hub and router combination, multiple computers cannot share internet access.
01 Possible Causes
Configuration errors
Hardware compatibility issues
Incorrect network settings
02 Troubleshooting Steps
Check Network Topology: Ensure the connection method between the hub and router is correct.
Check IP Address Configuration: Ensure all devices have correct IP address configurations, especially if the router’s DHCP service is properly enabled.
Check Routing Settings: Log in to the router management interface to check if static or dynamic routing protocols are correctly configured.
Test Physical Connections: Use the ping command to test the connectivity from devices connected to the hub to the router.
Update Firmware: Ensure all devices have the latest firmware versions and update them as needed.
03 Solutions
Reconfigure IP addresses and subnet masks to ensure all devices are in the same network segment.
Enable the router’s DHCP service to automatically assign IP addresses to connected devices.
Correctly configure static routes or enable dynamic routing protocols according to the network topology diagram.
If hardware is incompatible, consider replacing it with devices that support the required functions.
Vehicle gateways represent the central nervous system of modern connected vehicles, demanding exceptional reliability under challenging conditions. The extensive testing of the SV900 vehicle gateway provides valuable insights into the robustness a...
Wiring an inverter is simple: follow the wiring diagram! But how do you create that diagram? By understanding the control principles! What are the control principles? You need to know what an inverter is and what it does. If you don't understand t...
Wide Area Network (WAN) is one of the core components of enterprise networks. However, with the development, many drawbacks of traditional WAN have become apparent, such as high costs, limited flexibility, and difficulty in meeting the high-perfor...